Build a Safer DIY Air Cleaner With a Box Fan

Build an EPA-informed box-fan air cleaner with a MERV 13 filter and cardboard shroud, including placement, electrical safety and maintenance.

By RawColumn Editorial ·

Build a Safer DIY Air Cleaner With a Box Fan

A filter attached to a suitable box fan can be a temporary, lower-cost way to reduce airborne particles. US EPA testing found DIY designs can reduce simulated smoke particles, with multi-filter and shrouded designs offering performance advantages.

What this device can and cannot do

A MERV 13 filter is intended to capture particles carried through it. The unit does not remove every gas, create oxygen or make outdoor activity safe. During a smoke or severe-pollution event, close or ventilate the room according to current local advice and address indoor sources such as smoking, candles and frying.

Why the shroud matters

Covering the square corners around the circular blade path reduces recirculation at the front grille. More air is encouraged to travel through the filter rather than looping around the corners. The cardboard must stay outside the guard and clear of the blades.

Sources

Cost

Varies by local fan and filter prices

Tags

  • DIY air cleaner
  • box fan filter
  • MERV 13
  • indoor air

Steps

  • Title: Verify the fan before building
    Warning: Do not modify the fan’s wiring or bypass its guard. If the label or condition is uncertain, do not use it.
    Instruction: Find the manufacture label and UL or ETL certification mark. Use a fan made in 2012 or later. Inspect the plug, cable and guard; reject any unit with heat damage, loose wiring, a cracked guard or unstable controls.
  • Title: Read the filter arrow
    Instruction: Locate the airflow arrow printed on the filter frame. Position the filter on the intake side—the back of the fan—with the arrow pointing toward the fan.
  • Tip: Reusable fasteners make filter replacement easier.
    Title: Secure the filter
    Instruction: Centre the filter over the rear grille. Tape all four edges or use clamps/bungee cords so air cannot easily leak around the frame. Keep the plug, controls and motor vents unobstructed.
  • Title: Cut the shroud
    Warning: Unplug the fan before measuring or attaching anything near the guard.
    Instruction: Place cardboard over the front guard and mark the circular area swept by the blades. Cut out that circle, leaving the corners covered, then attach the shroud to the front without touching the blades.
  • Title: Place it safely
    Instruction: Set the unit upright on a stable, dry surface where the intake and outlet are unobstructed. Keep it away from curtains, water, cooking fumes, small children and trip routes. Plug it directly into a sound wall outlet where possible.
  • Title: Run and inspect
    Instruction: Start at a comfortable fan speed. After 15 minutes, check for unusual smell, noise, vibration or heat at the plug and motor. Switch off and unplug immediately if anything seems abnormal.
  • Title: Maintain the filter
    Instruction: Inspect the filter frequently during heavy smoke or dust. Replace it when visibly dirty, damaged, difficult for air to pass through or when odour persists. Write the installation date on the frame.

Tools

  • Tape measure
  • Marker
  • Utility knife or sturdy scissors
  • Straightedge

Prep Time

10 min

Materials

  • Name: 20 × 20 inch box fan made in 2012 or later with UL or ETL mark
    Price: Check locally
    Quantity: 1
  • Name: 20 × 20 inch MERV 13 filter, preferably 4 inches thick
    Price: Check locally
    Quantity: 1
  • Name: Corrugated cardboard for shroud
    Price: Reuse clean packaging
    Quantity: 1 sheet
  • Name: Strong duct tape or reusable clamps/bungee cords
    Price: Check locally
    Quantity: As needed
  • Name: Four non-slip pads
    Price: Optional
    Quantity: 4

Total Time

35 min

Difficulty

Beginner

Safety Tips

Use only a certified 2012-or-newer box fan in good condition; keep guards fitted; unplug before adjustment; keep the unit dry and clear of fabrics; never leave a damaged or overheating unit running; follow the fan manufacturer’s instructions. This device filters particles but does not supply oxygen, remove every gas or make an unsafe room safe. Follow local public-health advice during severe pollution or smoke.

Description

Attach a high-efficiency filter and cardboard shroud to a certified 20-inch box fan to make a temporary particle air cleaner. This build follows current US EPA guidance and emphasizes fan age, airflow direction, placement and filter replacement.

Prerequisites

Measure local products before purchase: filter and fan dimensions must match. People with asthma, heart/lung disease, pregnancy, advanced age or other vulnerability should follow clinician and local public-health guidance.

Active Work Time

25 min

Difficulty Explanation

No electrical modification is required. The main challenges are buying a correctly sized certified fan, orienting the filter correctly and making an airtight but serviceable connection.

Material Cost Breakdown

  • Cost: Local price
    Item: Certified fan
  • Cost: Local price
    Item: MERV 13 filter
  • Cost: Usually reusable/on hand
    Item: Fasteners and cardboard

Related articles

More Health articles